Full Auto Vacuum Blister Forming Machine For PVC Tray Lids Forming
25-45 Pcs / Min
This machine is suitable for forming PS/PVC/PET/PP plastic sheet
into various of containers,
boxes, dishes, trays, bowls and lids.
Touch screen control system, easy to operate, convenient to
1. 60 temperature points of Panasonic temperature control module is
adopted to control oven.
the temperature can be displayed in degrees, The temperature of
baking sheets can be adjusted
up and down .
2. Vacuum forming machine can memory the parameters , It will start
to produce, s long as opening
the number. Thus saving the time of adjusting of the machine and
increase the productivity
efficiency.Furnace heated by constant temperature can save energy
about 50% than common
3. Feeding part of automatic vacuum forming machine : automatic
transmission with duplex motor
Easy adjustment of the down gate size
4. Vibrate to take off from mold: Can adjust 0~9 times, twice
vacuum forming make sure the blister
5. No transmutation and easy to break off from mold. Repeatedly
cleaning with the wind of the end.
6. Electric control of up mold and middle gate, convenient
operation Imported vacuum pump with the
function of delay, one and twice vacuum forming.
7. Stainless steel making furnace, insulation, sealing structure,
effectively prevent heat loss.
1. The machine is designed total enclosed structure, which prevents
the dust and enhances the
product’s health quality.
2. This machine uses the double-row photoelectric control system,
the feeding width and length
even stepless adjustment(500mm-680mm, 700mm-1200mm), it is suitable
arrangement mould, the material using is high.
3. It adopts transducer to feed sheet, which is safe and reliable,
the feeding error is about
4. The heating system uses the horizontal type, which is convenient
to replace the damaged
5. The guide pillar is flinty processing, conforms GB CODE
(0.02mm-0.03mm) to strengthen
the down mould work smooth. The guide pillar need not lubricant,
which reduces pollution
and maintains neat.
6. The material institution is all controlled by PLC, the feeding
length is calm and correct.
7. Special wind-cool system makes the products shaping fast and
8. Poses the delay vacuum function and the second vacuum function.
9. The electric stove is all sealed, uses the heat preservation
cotton to keep temperature, and
saves power is approximately 40% compared to other similar types.
10.Demold by shaking, may shake when taking off mold, take on mold
for two times and protect
finished products, not deformation and not crack. Manual bottom
wind can be used in
sample, will not deform or damage mold.
11. The machine adopts PLC control system to make the machine
working more reliably.
12. The machine can achieve both of accuracy and stability during
high-speed operations, .
13. Equipped with a unique divided temperature control system and a
infrared ceramic heater
14. The major electronic devices and pneumatic components are
15. Work stability, safety and simple operation
III. Working process
PVC unreeling →PVC heating →blister tray forming →servo drawing
→blister tray cutting →PVC waste edge reeling →blister tray
delivery and stacking
IV.Main technical parameters
|FORMING LENGTH:||660-1250MM||ELECTRIC FURNACE POWER:||30KW|
|FORMING WIDTH:||410-710MM||MOTOR POWER:||4KW|
|POWER SUPPLY:||220/380V*3P 50/60HZ||VACUUM PUMP POWER:||3KW|
|AIR PRESSURE:||0.5-0.7MPa||CONTROL MODE:||PLC SCREEN TOUCH|
|PRODUCTION SPEED:||220-480TIMES/HOUR||BOTTOM TOOLING STROKE:||350MM|
V. Our Service
1. Customer's site installation, training & maintenance
2. 12-24 hours Online service by Email, Fax, Video Online for basic
setup and repairs
3. 12 months warranty for machine, life-long tech. support
4. Recommend equipment of top choice based on your requirements for
5. Examining mold drawings on your behalf to confirm optimum
structure size meeting high frequency process;
6. Providing assistance in manufacturing and modifying tools;
7. Our engineering instruction will guarantee your productive
manufacturing of top-quality products.
Questions 01. How Do You Pack the machines ?
RE: Our machines will be packed into wood case, (we will process
the wood case and make sure it is exporting standard, and no need
Questions 02. Is it difficult to install the machine ?
RE: For standard small machines, the machines will be packed with
no take apart, it comes to you to be a complete machine;
you just need to connect power and compressed air to machine, then
begin to operate the machine.
For large size machines, we will take the machine apart, on
condition that we do our best to keep the machine easy to assembly.
You will get install videos, and install instructions from us.
It will be an ABC thing to install machines at your side.
Questions 03. How Does Customer Use the machines ?
RE: We will provide you operation manual and diagram of machine in
For automatic machine and custom machine, we will provide operation
videos to you.
Questions 04. Does the machine need compressed air ?
RE: Generally speaking, if your factory with compressed air source,
then connect to machine.
If not, please buy a 2Psi -5 Psi air compressor.
If customer request to use Hydraulic pressure, please inform us
when put an order.
Questions 05. Does the machine power voltage meet buyers' factory
RE: We can make machine with voltage like:
frequency: 50 - 60HZ Phases: single phase / 3 phases
Voltage: 110V / 220V / 380V/ 415V/ 440V / On request
Please kindly inform us what frequency/phases/voltage you want,
when you put order to us.
Questions 06. Could you make die / mould for me, if I buy machine
RE: We design and make moulds up to product sample or drawings, we
charge the mould price at facory cost price.
Questions 07. Can I visit you factory to check machines on-site ?
RE: We are manufacturer, and we welcome customers to visit our
We located in Shenzhen, China; you may come to us by following:
a) Via. Hongkong to Shenzhen :
please reach check points between Hongkong and Shenzhen, we will
arrange to pick you up from Check-point like Shekou, Lohu
b) Via. Guangzhou to Shezhen;
you may come by train to Shenzhen Luohu Station / Shenzhen North
we will arrange to pick you up from station.
c) Via. Shenzhen Airport :
Please inform us your flight number and contact information before
you come, we will meet you at airport.
Questions 08. What Should I bring when I visit your factory?
RE: For special product design and develop, we request you bring a
piece of testing material, you can test on our machines on-site.
For common product, it is enough to show us product pictures or
material together. However, when an HF-welded seam is stressed, the
load is absorbed by the material surfaces, which of course means
that the HF-welded seam is stronger. Furthermore, the seam created
with HF can be welded in a manner that provides a uniform
transition without splices between the joined materials. There is
no space through which dirt, moisture or bacteria can penetrate and
impair the product’s strength and durability.